| Communications |
| Ethernet |
10/100 Mbps, auto-switching, auto-negotiating, auto-discovery, full/half duplex, TCP/IP, UDP/IP, CIP, DHCP, SSL, SSH, SFTP (SSH File Transfer Protocol) |
| USB Device |
USB device port for computer console (setup) |
| Audio |
| Input Signal Types |
Balanced or unbalanced analog line-level |
| Output Signal Types |
4/8 Ohm, 70 or 100 Volt direct-coupled |
Operating Modes
(Configurable via Avia Audio Tool software) |
Mono: Each channel is configurable to operate independently from all other channels
Stereo:The output channels are configurable to operate as a stereo pair with linked control settings
Bridged: The output channels are configurable to operate as an 8 Ohm bridged mono output
4/8Ω Mode: Each channel is configurable for 4/8 Ohm
“Lo-Z” output
70V/100V Mode: Each channel is configurable for
70/100 Volt “Hi-Z” output
|
| Output Power |
800 Watts per channel @ 4-8 Ohms or
70/100 Volts nominal; 1200 Watts per bridged pair of channels @ 8 Ohms
|
| Power Throttle |
800, 700, 600, 500, 400, 300, 250, 200, 150, 125, 100, 75, 50 Watts per channel |
| Frequency Response |
20 Hz to 20 kHz ±0.5 dB at 1 Watt, 4-8 Ohms;
200 Hz to 20 kHz ±0.5 dB at 1 Watt, 70/100 Volts |
| High Pass Filter |
-3 dB @ 80 Hz, 12 dB per octave in 70V or 100V mode |
| THD+N |
<0.05% @ 1 kHz at 3 dB below clipping |
| S/N Ratio |
>103 dBA, 20 Hz to 20 kHz |
| Channel Separation |
>70 dB |
| Input Sensitivity |
1.29 Vrms, +4 dBu (balanced) for full rated output power |
| Fault Protection |
Over Current: Protects each channel individually against an excessive speaker load or shorted speaker line
DC Offset: Protects each channel and speaker line against DC voltages sensed at each output
Over Temperature: Protects the amplifier power supply and each channel against overheating due to poor ventilation or excessive temperature
Under Voltage: Protects the amplifier if the internal power supply voltage is below tolerance due to excessive output levels or insufficient line voltage;
Note: All faults report to the control system, and indicate on the front panel and in the software tool.
|
| Output Relays |
Disconnects the speaker line at each output under fault conditions, and during startup and shutdown |
| Audio Ramp |
Ramps each channel’s audio level to its last setting after the corresponding output relay has closed following startup or fault recovery; ramp time 130 milliseconds |
| Connectors |
| LINE INPUTS 1 & 2 |
(2) 3-pin 3.5 mm detachable terminal blocks;
Balanced line-level audio inputs;
Maximum Input Level: 12.3 Vrms, +24 dBu;
Input Impedance: 20k Ohms balanced |
| SPEAKER OUTPUTS 1 & 2 |
(2) 2-pin 7.62 mm reversed gender 20A detachable terminal blocks;
Power amplifier outputs;
Wire Size: Terminals accept up to 12 AWG (3.31 mm²);
Note: Output is direct-coupled in all modes for all load types, not transformer isolated |
| LAN |
(1) 8-pin RJ45 female;
10Base-T/100Base-TX Ethernet LAN port |
| 100-240V~ 50/60Hz 4A-2A |
(1) IEC 60320 C14 main power inlet;
Mates with removable power cord (included) |
| G |
(1) 6-32 screw;
Chassis ground lug |
| COMPUTER (front) |
(1) USB Type B female;
USB computer console port (for setup only) |
| Controls & Indicators |
| PWR |
(1) Bi-color green/amber LED, indicates operating power supplied from AC line power, amber indicates startup in progress, green indicates normal operation and a connection to the LAN, alternating green/amber indicates absence of a network connection |
| RESET |
(1) Recessed pushbutton, restores last saved settings |
| STATUS, FAULT 1 & 2 |
(2) Red LEDs, each indicates a fault on the corresponding channel with specifics indicated below |
| STATUS, CURRENT 1 & 2 |
(2) Blue LEDs, each indicates an over-current fault condition on the corresponding output |
| STATUS, DC 1 & 2 |
(2) Blue LEDs, each indicates a DC offset fault condition on the corresponding channel |
| STATUS, THERM 1 & 2 |
(2) Blue LEDs, each indicates an over-temperature fault condition on the corresponding channel |
| STATUS, 70V-100V 1 & 2 |
(2) Blue LEDs, each indicates the corresponding channel is configured for 70 Volt / 100 Volt operation |
| VU 1 & 2 |
(2) 5-segment LED bar graph audio level meters for each corresponding output; each contains (4) blue LEDs for -40dB, -30dB, -20dB, and -10dB, and (1) red LED for CLIP |
| LINE INPUTS 1 & 2 (rear) |
(2) Screwdriver-adjustable rotary controls, each adjusts the input attenuation level for the corresponding channel |
| LAN (rear) |
(2) LEDs, green LED indicates Ethernet link status, amber LED indicates Ethernet activity |
| SETUP (rear) |
(1) Red LED and (1) pushbutton for Ethernet setup, flashes while updating firmware |
| Power Switch (rear) |
(1) Rocker switch, turns main power on or off |
| Circuit Breaker Reset (rear) |
(1) Push button switch, resets 10A circuit breaker |
| Power |
| Main Power |
4-2 Amps @ 100-240 Volts AC, 50/60 Hz, 10 Amps max. |
| Input Power |
300 Watts |
| Power Consumption |
300 Watts, all channels driven at 1/8th output power;
50 Watts @ 120VAC / 60 Watts @ 230VAC, all channels idle |
| Environmental |
| Temperature |
41° to 104°F (5° to 40°C) |
| Humidity |
10% to 90% RH (non-condensing) |
| Heat Dissipation |
1025 BTU/hr, all channels driven at 1/8th output power;
240 BTU/hr, all channels idle |
| Construction |
| Chassis |
Metal, variable-speed fan-cooled, vented sides |
| Front Panel |
Metal, black finish with polycarbonate label overlay |
| Mounting |
Freestanding or 1 RU 19-inch rack-mountable (front rack ears and rear support brackets included) |
| Dimensions |
| Height |
1.72 in (44 cm) |
| Width |
17.28 in (439 mm);
19.00 in (483 mm) with rack ears |
| Depth |
14.59 in (371 mm) |
| Weight |
| 13.7 lb (6.2 kg) |
| Compliance |
| UL 60065, FCC Class A commercial use |