| Load Ratings |
| |
Dimmer Channels |
GLPAC-DIMFLV4 Series: 4;
GLPAC-DIMFLV8 Series: 8;
GLPAC-DIMFLV8-4E Series: 4 and 4, isolated |
| |
Per Channel |
16 Amps @ 100 to 277 Volts AC, 50/60 Hz |
| |
Dim Load Types |
0-10 Volt fluorescent ballast or LED driver (4-wire);
60 mA max current sink |
| |
Switch Load Types |
Fluorescent ballast, incandescent, magnetic low-voltage, electronic low-voltage, neon/cold cathode, high-intensity discharge, LED, motor |
| |
Relay Lifetime |
Resistive rating: 100,000 on/off operations, 50 Amps @ 277 Volts AC
General rating: 50,000 on/off operations, 16 Amps @ 120/277 Volts AC |
| Power Requirements |
| |
Main Power |
100-277 Volts AC, 50/60Hz, supplied via channel 1 (LINE 1, NEUT) |
| |
Available Cresnet Power |
10 Watts at 24 Volts DC, shared with occupancy and photosensor ports |
| Connectors (Class 1) – 4-Channel Models Only |
| |
NEUT |
(2) Terminal blocks, paralleled, line input neutral |
| |
LINE 1 - LINE 4 |
(8) Terminal blocks, paralleled, line power inputs |
| |
SW1 - SW4 |
(4) Terminal blocks, switch channel outputs |
| |
0-10V DIM (+,-) 1-4 |
(1) 8-position terminal block, dim channel output, galvanically isolated; may be wired as Class 1 or Class 2 |
| Connectors (Class 1) – 8-Channel Models Only |
| |
NEUT |
(2) Terminal blocks, paralleled, line input neutral |
| |
LINE 1 - LINE 8 |
(16) Terminal blocks; 2 connections per channel, paralleled, allows for easy daisy chaining; line power inputs |
| |
SW1 - SW8 |
(8) Terminal blocks, switch channel outputs |
| |
0-10V DIM (+,-) 1-8 |
(2) 8-position terminal block, dim channel output, gavanically isolated;
May be wired as Class 1 or Class 2 |
| Connectors (Class 2) |
| |
NET SLAVE |
(1) 4-pin 3.5mm detachable terminal block; Cresnet ports for connection to main control processor or other GLPAC-DIMFLVs, does not output 24 Volts DC |
| |
OVR |
(1) 2-pin 3.5mm detachable terminal block, comprising (2) inputs for external contact closures to trigger the preset Override state |
| |
NET LOCAL |
(1) 4-pin 3.5mm detachable terminal block; Cresnet ports for connection to local devices such as keypads, shade controllers, and touch screens; outputs 24 Volts DC |
| |
RELAY 1-4 (-PM models only) |
(1) 8-pin 3.5mm detachable terminal blocks comprising (4) normally open, isolated relays; Programmable or used for interfacing to local Variable Air Volume box to indicate room occupancy; Rated 1 Amp, 30 Volts DC |
| |
INPUT 1-8 |
(1) 9-pin 3.5mm detachable terminal block comprising (8) digital input ports, referenced to ground |
| |
OCCUPANCY SENSOR INPUT 1-4 |
(1) 6-pin 3.5mm detachable terminal block comprising (4) occupancy sensor inputs, (1) +24VDC, and (1) GND port (provides sensors with power) |
| |
PHOTOCELL 1-4 |
(1) 6-pin 3.5mm detachable terminal block comprising (4) photocell sensor inputs, (1) +24VDC, and (1) GND port (provides sensors with power); Min-change setting can be adjusted to control how often sensor reports changes in values |
| |
USB |
(1) USB Type B console port, for communication with Crestron Toolbox™ |
| |
LAN |
(1) 8-wire RJ45 with 2 LED indicators; 10/100BaseT Ethernet port; Green LED indicates link status; Yellow LED indicates Ethernet activity |
| Controls & Indicators |
| |
MODE |
(2) 7-Segment green LED digits and (2) miniature pushbuttons for setting mode during setup or local control |
| |
VALUE |
(2) 7-Segment green LED digits and (2) miniature pushbuttons for setting value |
| |
SAVE |
(1) Red LED and (1) miniature pushbutton for saving settings |
| |
CANCEL |
(1) Red LED and (1) miniature pushbutton for cancelling current operation |
| |
PWR |
(1) Green LED; solid illumination indicates line power is applied to NEUT and LINE1 |
| |
HW-R |
(1) Recessed miniature pushbutton for hardware reset (reboots the processor) |
| |
SW-R |
(1) Recessed miniature pushbutton for software reset (restarts the SIMPL program) |
| |
NET-C |
(1) Yellow LED; indicates communication with main control processor (if being used) |
| |
NET-L |
(1) Yellow LED; indicates communication with local devices |
| |
MSG |
(1) Red LED; indicates control system has generated an error message |
| |
OVR |
(1) Red LED and (1) miniature pushbutton for enabling override mode |
| |
ON/OFF |
(8) Red LEDs and (8) miniature pushbuttons for individual manual channel activation and dimming |
| Enclosure |
| |
Surface mount metal box enclosure, suitable for mounting in plenum airspace |
| Environmental |
| |
Temperature |
32° to 104°F (0° to 40°C) |
| |
Humidity |
10% to 90% RH (non-condensing) |
| Dimensions |
| |
Height |
12.13 in (308 mm) |
| |
Width |
14.13 in (359 mm) |
| |
Depth |
4.06 in (103 mm) |
| Electrical Regulatory Certifications |
| |
Relays tested and certified for Electronic Ballasts according to UL508, Section 41 (Endurance Test) and Section 61C (Electronic Ballasts) |
| |
IEC60669-2-1, Section 19.102 (Contact mechanisms incorporated in electronic switches, intended for fluorescent lamp circuits or other capacitive loads) |
| |
CE |
| |
UL924 Listed upon request |
| |
CEC Title 24 2013 Compliant |