| Video |
| Switcher |
8x2 auto-switching or manual, audio-follows-video, Crestron Auto-Locking® and QuickSwitch HD™ technologies |
| Scaler (mirrored HDMI and DM Essentials outputs) |
4K60 4:4:4 video scaler with motion-adaptive deinterlacing, intelligent frame rate conversion; Deep Color support; HDR10, HDR10+, and Dolby Vision support; content-adaptive noise reduction; and 3:2/2:2 pull-down detection and recovery |
| Input Signal Types |
HDMI with HDR10, HDR10+, and Dolby Vision support, Deep Color support, and 4K60 4:4:4 support (DVI and Dual-Mode DisplayPort™ interface compatible3) on Inputs 1-6, DM Essentials with Deep Color and 4K on Inputs 7-8 |
| Output Signal Types |
HDMI, DM Essentials, and HDBaseT with HDR10, HDR10+, and Dolby Vision pass-through support, Deep Color support, and 4K60 4:4:4 support (DVI compatible4) |
| Copy Protection |
HDCP 2.3 |
Maximum Resolutions
Common resolutions for the HDMI and DM Essentials inputs are listed in the following table.
Scan
Type |
Resolution |
Frame
Rate |
Color
Sampling |
Color
Depth |
| Progressive |
4096x2160 DCI 4K and
3840x2160 4K UHD |
24 Hz |
4:4:4 |
36 bit |
| 30 Hz |
4:4:4 |
36 bit |
| 60 Hz |
4:2:2 |
36 bit |
| 60 Hz |
4:4:4 |
24 bit |
| 2560x1600 WQXGA |
60 Hz |
4:4:4 |
36 bit |
| 1920x1080 HD 1080p |
60 Hz |
4:4:4 |
36 bit |
Interlaced
(Input Only) |
1920x1080 HD 1080i |
30 Hz |
4:4:4 |
36 bit |
|
| Scaler Output Resolutions, HDMI and DM Essentials |
Auto-HDMI
Auto-DM Lite
1280x720p@50Hz (720p50)
1280x720p@60Hz (720p60)
1920x1080p@24Hz (1080p24)
1920x1080p@25Hz (1080p25)
1920x1080p@30Hz (1080p30)
1920x1080p@50Hz (1080p50)
1920x1080p@60Hz (1080p60)
3840x2160p@24Hz
3840x2160p@25Hz
3840x2160p@30Hz
3840x2160p@50Hz
3840x2160p@60Hz
4096x2160p@24Hz
4096x2160p@25Hz
4096x2160p@30Hz
4096x2160p@50Hz
4096x2160p@60Hz |
| Audio, General |
| Audio Inputs |
Two mono 1-channel MIC/LINE inputs
Six mono 1-channel LINE inputs
One stereo 2-channel LPCM audio extracted from the selected HDMI or DM Essentials input source
|
| Audio Outputs |
One mirrored HDMI 1 and DM Essentials 1 audio output
One mirrored HDMI 2 and DM Essentials 2 audio output
One AUX 1 output, stereo 2-channel
One AUX 2 output, stereo 2-channel
|
| Analog-to-Digital Conversion |
24-bit 48 kHz |
| Digital-to-Analog Conversion |
24-bit 48 kHz |
| Audio, Digital Inputs (HDMI 1-6 and DM 7-8) |
| Input Signal Types |
HDMI (Dual-Mode DisplayPort interface compatible3), DM Essentials |
| Formats |
Dolby Digital®, Dolby Digital EX, Dolby Digital Plus, Dolby® TrueHD, Dolby Atmos®, DTS®, DTS-ES, DTS 96/24, DTS HD® High Res, DTS-HD Master Audio, DTS:X®, LPCM up to 8 channels |
| Audio, Microphone/Line Inputs (CH1-CH2) |
| Input Signal Type |
Mono analog |
| Gain Range |
-10 dB to +10 dB in 1 dB increments |
| Phantom Power |
+48 VDC, 12 mA, enable or disable per channel |
| Mute |
Enable or disable per channel |
| Audio, Line Inputs (CH3-CH8) |
| Input Signal Type |
Mono analog |
| Gain Range |
-10 dB to +10 dB in 1 dB increments |
| Balanced Line Input Level |
4 Vrms |
|
Unbalanced Line Input Level
|
2 Vrms |
| Line Input Impedance |
>10k ohms |
| Audio, Digital Output |
| Output Signal Type |
HDMI |
| Formats |
Dolby Digital, Dolby Digital EX, Dolby Digital Plus, Dolby TrueHD, Dolby Atmos, DTS, DTS-ES, DTS 96/24, DTS HD High Res, DTS-HD Master Audio, DTS:X, LPCM up to 8 channels |
| Source Gain |
-80 dB to +20 dB adjustment range, plus Mute |
| Volume Control |
-80 dB to +20 dB adjustment range, plus Mute |
| Delay |
0 to 150 ms adjustment range |
| Audio, Analog Line Output |
| Output Signal Type/Format |
Stereo 2-channel |
| Frequency Response |
±0.5 dB, 20 Hz to 20 kHz |
| THD+N |
<0.005%, 1 kHz, 4 Vrms |
| S/N Ratio |
>95 dB, 4 Vrms, 20 Hz to 20 KHz, A‑weighted |
| Crosstalk |
>90 dB, 1 KHz, for multiple inputs only |
| Stereo Separation |
>80 dB, 20 Hz to 20 kHz |
| Volume Control |
-80 dB to +20 dB adjustment range, plus Mute, Mono, and Stereo |
| Communications |
| Ethernet |
100/1000 Mbps, auto-switching, auto-negotiating, auto-discovery, full/half duplex, DHCP, Web browser setup and control, Crestron control system integration, IEEE 802.1X, Secure CIP, Authentication, SSH/SSL, TLS |
| USB |
For firmware loading and configuration management and to power a USB powered device |
| HDMI |
HDCP 2.3, EDID, CEC |
| DM Essentials |
HDCP 2.3 and EDID |
| HDBaseT |
HDCP 2.3 |
| Connectors |
| MIC/LINE CH1-CH2 |
(2) 3-pin 3.5 mm detachable terminal blocks;
Balanced mono microphone/line audio inputs |
| LINE INPUT CH3-CH8 |
(6) 3-pin 3.5 mm detachable terminal blocks;
Balanced mono line-level audio inputs |
| AUX OUT 1-2 |
(2) 5-pin 3.5 mm detachable terminal blocks;
Balanced stereo line-level audio outputs;
Output Impedance: <200 Ohms;
Maximum Output Level: 4 Vrms balanced |
| HDMI INPUTS 1-6 |
(6) 19-pin Type A connector, female;
HDMI digital video/audio input (DVI and Dual-Mode DisplayPort interface compatible3) |
| DM INPUTS 7-8 |
(2) 8-pin RJ-45 yellow connectors, female, shielded;
DM Essentials input ports for connection to DM Essentials transmitters5 |
| DM OUTPUT 1 |
(1) 8-pin RJ-45 blue connector, female, shielded;
DM Essentials output port (HDBaseT standard compliant) for connection to a DM Essentials receiver, DMPS Essentials switcher, or HDBaseT device6;
Mirrored with HDMI OUTPUT 1 |
| HDMI OUTPUT 1 |
(1) 19-pin Type A connector, female;
HDMI digital video/audio output (DVI compatible4);
Mirrored with DM OUTPUT 1 |
| DM OUTPUT 2 |
(1) 8-pin RJ-45 blue connector, female, shielded;
DM Essentials output port (HDBaseT standard compliant) for connection to a DM Essentials receiver, DMPS Essentials switcher, or HDBaseT device;6
Mirrored with HDMI OUTPUT 2 |
| HDMI OUTPUT 2 |
(1) 19-pin Type A connector, female;
HDMI digital video/audio output (DVI compatible4);
Mirrored with DM OUTPUT 2
|
| LAN |
(1) 8-pin RJ-45 connector, female;
100BASE-TX/1000BASE-T Ethernet port |
| 100-240VAC 1.8-0.7A 50/60 Hz |
(1) IEC 60320 C14 mains power inlet;
Mates with removable power cord, included |
| NOTE: This power connection powers both the HD‑PS622 and the connected DM Essentials transmitters and receivers. When connected to the HD‑PS622, the DM Essentials transmitters and receivers must not be connected to power.7 |
| G |
(1) 6-32 screw, chassis ground lug |
| SERVICE |
(1) USB 2.0 Type A connector, female;
For firmware loading and configuration management;
Can also provide up to 5 V 500 mA power to a USB powered device |
| Controls and Indicators |
| PWR |
(1) LED. Amber indicates that the device is booting. Green indicates that the device is operational. |
| AUTO |
(1) Push button to enable or disable automatic switching and (1) green LED to indicate that automatic switching is enabled. |
| SETUP |
(1) Red LED and (1) push button for display of IP address on connected HDMI and DM Essentials outputs |
| INPUT 1-8 |
(8) Push buttons for manual input selection and (8) LEDs. Green indicates that the corresponding input is routed to an output. Amber indicates that a source is detected at the corresponding input but is not routed to an output. |
| OUTPUT 1-2 |
(2) Push buttons for manual output selection and (2) LEDs. Green indicates that a display or other destination device is detected and the corresponding output is transmitting video. Amber indicates that a display or other destination device is detected but no video is routed to the corresponding output. |
| FOLLOW |
(1) Push button to enable or disable Follow Output mode and (1) LED. Green indicates that Follow Output mode is enabled, which causes the selected HDMI or DM Essentials input to be routed to HDMI and DM Essentials outputs 1 and 2 simultaneously. |
| Ethernet |
(2) LEDs on RJ-45 LAN connector.
Link status LED: Green indicates that a 100BASE-TX link is established. Amber indicates that a 1000BASE-T link is established.
Ethernet activity LED: Flashing amber indicates Ethernet activity. |
| DM Essentials |
(2) LEDs on RJ-45 DM Essentials connectors. Green indicates that a DM Essentials link is established. Flashing amber indicates non-HDCP video and solid amber indicates HDCP video. |
| Power |
| Mains Power |
100-240VAC 1.8-0.7A 50/60 Hz |
| NOTE: The AC mains power connection powers both the HD‑PS622 and connected DM Essentials transmitters and receivers. When connected to the HD‑PS622, the DM Essentials transmitters and receivers must not be connected to power.7 |
| Power Consumption |
72 W typical |
| Environmental |
| Temperature |
32° to 104° F (0° to 40° C) |
| Humidity |
10% to 90% RH (non‑condensing) |
| Heat Dissipation |
164 BTU/hr typical |
| Acoustic Noise |
32 dBA typical |
| Construction |
| Chassis |
Metal, black finish, vented sides |
| Mounting |
1 RU 19-inch rack-mountable (rack ears included) |
| Dimensions |
| Height |
1.72 in. (44 mm) |
| Width |
17.33 in. (441 mm) without rack ears
19.00 in. (483 mm) with rack ears (included) |
| Depth |
10.82 in. (275 mm) |
| Weight |
| 8.0 lb (3.63 kg) |
| Compliance |
| Regulatory Model |
M202004002 |
| Bureau Veritas Listed for US & Canada, IC, CE, FCC Part 15 Class B digital device |
| Maximum DM Essentials Transmission Distance |
| Resolution |
Frame Rate (Hz) |
Color Sampling |
Color Depth |
Cable Type2 |
| 1920x1080 HD 1080i |
30 |
4:4:4 |
12 bit |
230 ft (70 m) |
195 ft (60 m) |
| 1920x1080 FHD 1080p |
60 |
4:4:4 |
8, 12 bit |
| 1600x1200 UXGA |
60 |
4:4:4 |
8, 12 bit |
| 2048x1080 DCI 2K |
60 |
4:4:4 |
8, 12 bit |
| 1920x1200 WUXGA |
60 |
4:4:4 |
8, 12 bit |
| 2048x1152 QWXGA |
60 |
4:4:4 |
8, 12 bit |
| 2560x1080 UWFHD |
60 |
4:4:4 |
8 bit |
| 2560x1440 WQHD Reduced Blanking |
60 |
4:4:4 |
8 bit |
| 2560x1600 WQXGA Reduced Blanking |
60 |
4:4:4 |
8 bit |
| 2048x1152 QWXGA |
60 |
4:4:4 |
12 bit |
| 3840x2160 4K UHD and 4096x2160 DCI 4K |
30 |
4:2:2 |
12 bit |
| 30 |
4:4:4 |
8 bit |
| 60 |
4:2:0 |
8 bit |
| 3840x2160 4K UHD and 4096x2160 DCI 4K |
30 |
4:4:4 |
12 bit |
130 ft (40 m) |
100 ft (30 m) |
| 60 |
4:2:0 |
12 bit |
| 60 |
4:2:2 |
12 bit |
| 60 |
4:4:4 |
8 bit |
|