| Video |
| Input Signal Types |
HDMI with HDR10, HDR10+, Dolby Vision, Deep Color, 4K60 4:4:4 support1, 2 (DVI and Dual-Mode DisplayPort™ interface compatible3) |
| Output Signal Types |
HDMI with HDR10, HDR10+, Dolby Vision, Deep Color, and 4K60 4:4:4 support1, 2 (DVI compatible4) |
| Switcher |
4x1 digital AV switcher |
| Copy Protection |
HDCP 2.3 |
| Maximum Resolutions |
Common resolutions are listed in the following table. |
Scan
Type |
Resolution |
Frame
Rate |
Color
Sampling |
Color
Depth |
| Progressive |
4096x2160 DCI 4K
and 3840x2160 4K UHD |
24 Hz |
4:4:4 |
36 bit |
| 30 Hz |
4:4:4 |
36 bit |
| 60 Hz |
4:2:2 |
36 bit |
| 60 Hz |
4:4:4 |
24 bit |
| 2560x1600 WQXGA |
60 Hz |
4:4:4 |
36 bit |
| 1920x1080 HD 1080p |
60 Hz |
4:4:4 |
36 bit |
Interlaced
(Input Only) |
1920x1080 HD 1080i |
30 Hz |
4:4:4 |
36 bit |
| NOTE: Custom resolutions that do not exceed 4096 pixels in width and 2160 pixels in height are supported at pixel clock rates up to 600 MHz. |
|
| Audio - General |
| Digital-To-Analog Conversion |
24-bit 48 kHz |
| Frequency Response |
±0.5 dB, 20 Hz to 20 kHz |
| THD+N |
<0.005%, 1 kHz, 10 dBV |
| S/N Ratio |
>95 dB, 10 dBV, 20 Hz to 20 KHz, A-weighted |
| Crosstalk |
≤90 dB, 1 KHz, for multiple inputs only |
| Stereo Separation |
≤80 dB, 20 Hz to 20 kHz |
| Audio - Source Inputs |
| Input Signal Type |
HDMI (Dual-Mode DisplayPort interface compatible3) |
| Formats |
Dolby Digital®, Dolby Digital EX, Dolby Digital Plus, Dolby® TrueHD, Dolby Atmos®, DTS®, DTS-ES, DTS 96/24, DTS HD® High Res, DTS-HD Master Audio, DTS:X®, LPCM up to 8 channels |
| Audio - Digital Output |
| Output Signal Type |
HDMI |
| Formats |
Dolby Digital, Dolby Digital EX, Dolby Digital Plus, Dolby TrueHD, Dolby Atmos, DTS, DTS-ES, DTS 96/24, DTS HD High Res, DTS-HD Master Audio, DTS:X, LPCM up to 8 channels |
| Source |
-80 dB to +20 dB adjustment range, plus Mute |
| Master Volume |
-80 dB to +20 dB adjustment range, plus Mute |
| Audio - Analog Line Output |
| Output Signal Type/Format |
Stereo 2-channel |
| Volume Control |
-80 dB to +20 dB adjustment range, plus Mute, Mono, and Stereo |
| Communications |
| Ethernet |
100/1000 Mbps, auto-switching, auto-negotiating, auto-discovery, full/half duplex, DHCP, Web browser setup and control, Crestron control system integration, IEEE 802.1X, Secure CIP, Authentication, SSH/SSL, TLS |
| USB |
For firmware loading and configuration management and to power a USB powered device |
| HDMI |
HDCP 2.3, EDID, CEC |
| Connectors |
| HDMI IN 1-4 |
(4) 19-pin Type A connector, female;
HDMI digital video/audio input (DVI and Dual-Mode DisplayPort interface compatible3) |
| HDMI OUT |
(1) 19-pin Type A connector, female;
HDMI digital video/audio output (DVI compatible4) |
| AUDIO OUT, AUX |
(2) 5-pin 3.5 mm detachable terminal block;
Balanced/unbalanced stereo line-level audio output;
Output Impedance: <100 Ohms;
Maximum Output Level: 4 Vrms balanced, 2 Vrms unbalanced |
| LAN PoE |
(1) 8-pin RJ-45 connector, female;
100BASE-TX/1000BASE-T Ethernet port;
PoE (Power over Ethernet) powered device (PD) port;
IEEE 802.3at Type 1 (802.3af compatible) Class 0 (12.95 W) compliant5 |
| 24 VDC 0.75 A |
(1) 2.1 x 5.5 mm DC power connector;
24 VDC power input;
PW-2407WU power pack (sold separately) |
| SERVICE |
(1) USB Type A female;
For firmware loading and configuration management;
Can also provide up to 5 V 500 mA power to a USB powered device |
| G |
(1) 6-32 screw, chassis ground lug |
| Controls and Indicators |
| PWR |
(1) LED. Amber indicates that the device is booting. Green indicates that the device is operational. |
| AUTO |
(1) Push button to enable or disable automatic switching and (1) green LED to indicate that automatic switching is enabled |
| INPUT 1-4 |
(4) Push buttons for manual input selection and (4) LEDs. Green indicates that the corresponding input is routed to the output.
Amber indicates that a source is detected at the corresponding input but is not routed to the output. |
| SETUP |
(1) Red LED and (1) push button for display of IP address on connected HDMI output |
| Ethernet |
(2) LEDs on RJ-45 LAN connector.
Link status LED: Green indicates that a 100BASE-TX link is established. Amber indicates that a 1000BASE-T link is established.
Ethernet activity LED: Flashing amber indicates Ethernet activity. |
| Power |
| PoE |
IEEE 802.3at Type 1 (802.3af compatible) Class 0 (12.95 W) compliant, capable of being powered by PoE power sourcing equipment (PSE)5 |
| Power Pack (Optional) |
0.75 A @ 24 VDC;
100-240 VAC, 50/60 Hz;
Model: PW-2407WU (sold separately) |
| Power Consumption |
10 W typical |
| Environmental |
| Temperature |
32° to 104° F (0° to 40° C) |
| Humidity |
10% to 90% RH (non-condensing) |
| Heat Dissipation |
33 BTU/hr typical |
| Acoustic Noise |
Not applicable (fanless) |
| Construction |
| Chassis |
Metal, black finish, vented sides |
| Mounting |
Surface-mountable or attachment to a single rack rail |
| Dimensions |
| Height |
8.52 in. (217 mm) |
| Width |
7.0 in. (178 mm) |
| Depth |
1.34 in. (34 mm) |
| Weight |
| 1.8 lb (0.82 kg) |
| Compliance |
| Regulatory Model |
M201946001 |
| Bureau Veritas Listed for US & Canada, IC, CE, FCC Part 15 Class B digital device |